Eastside Lumber The Strategy

BILT-BLOCKS · EASTSIDE LUMBER · KANSAS CITY

The Catalog of Parts

In 1908 Sears sold houses as kits of numbered parts. We're bringing the parts back: a wall panel, a floor truss and a roof truss, built in a shop and set on site. Three parts. Any building.

Scroll to take the parts apart and put them back together.

PLATE 1

The Wall Panel

One panel, seven layers, built flat on a shop table and stood up on site. The layers are the same ones permitted on our three-story home at 2509 Michigan.

  • R-23 batt in the wall cavity + R-8.6 continuous outside it = R-31.6 nominal
  • 2×6 framing
  • vented rainscreen

    On center (o.c.) is the spacing between studs. The KCMO pre-approved plans use 16″. Our permitted three-story uses 24″ advanced framing, which means less wood and more insulation.

    PLATE 2

    The Floor Truss

    An open-web truss: a top chord and a bottom chord (the long members) joined by short diagonal webs. The open web is the point. Plumbing, ducts and wiring pass through it, so no trade ever cuts the structure. Set side by side at 24″ on center, the trusses become a floor cassette: a deck on top, the ceiling of the room below already hung underneath.

    • Chord: the top or bottom member of a truss
    • Web: the diagonal members between them
    • Cassette: a floor or roof section built as one piece

    DETAIL A

    Wall to Floor

    This is the joint that makes a second story. The lower wall panel ends in a top plate. The floor trusses bear on that plate, a rim board closes the floor edge, and the deck goes down. The upper wall panel lands on the deck and the same detail repeats at every floor.

    • Top plate: the doubled board along the top of a wall panel
    • Rim board: the board that caps the ends of the floor trusses

      Typical connection, engineered per project.

      PLATE 3

      The Roof Truss

      One roof truss, three profiles. Gable for a pitched roof, single-slope for a shed roof, flat for a roof deck behind a parapet. The pitched trusses have a raised heel at the wall, so the attic insulation runs full depth all the way to the edge.

      • Heel: the end of the truss where it sits on the wall
      • Flat truss: 14″ deep, parallel chords

      DETAIL B

      Wall to Roof

      At the top, the truss heel sits on the wall panel's top plate, a metal tie-down clip locks the two together against wind uplift, and the roof sheathing closes the box.

        Typical connection, engineered per project.

        No. 05

        The Bungalow

        One story, three bedrooms, two baths, 1,065 square feet. This is one of Kansas City's pre-approved house plans, so the permit drawings already exist. Wall panels and a gable roof.

        • 1 story
        • gable roof
        • KCMO pre-approved plan

          Your kit contains

          Quantities generated from the 4 ft module — approximate, not a takeoff.

          No. 34

          The Townhome Row

          Three stories, five homes in a row, on our standard 20-foot and 16-foot bays. This is the home we designed for Kansas City's urban core: the same wall panel, now stacked three high, with floor trusses spanning between the party walls.

          • 3 stories
          • flat roof with parapet
          • 5 homes, 92′ × 34′

            Your kit contains

            Quantities generated from the 4 ft module — approximate, not a takeoff.

            No. 60

            The Apartment

            Illustrative — not a current project

            Four stories with a center corridor. The same panel and the same two trusses, repeated. Nothing new is invented for the bigger building.

            • 4 stories
            • flat roof
            • center corridor

              Your kit contains

              Quantities generated from the 4 ft module — approximate, not a takeoff.

              Same panel. Same factory.

              Send us your plans

              If you build houses, townhomes or apartments, send us the drawings. We'll show you how they break down into our three parts and what goes on the truck.

                Open in your mail app
                Sheet KP-02 · Bilt-Blocks kit of parts · Assemblies from the permitted 2509 Michigan set and the KCMO pre-approved plans. Connections are typical and engineered per project. Quantities are approximate, not a takeoff.
                This diagram needs WebGL. Open it in a current Chrome, Safari or Edge.